About PoE from Milleteknik
The series is designed to power PoE devices such as access systems, surveillance cameras and other equipment that can be operated with Power over Ethernet.
PoE injector 1p S
 |
The picture shows PoE injector 1p S with battery, (not included)
How the PoE injector powers devices connected to the power supply
The PoE injector can drive, for example, a surveillance camera.
Connect external device to be powered via PoE injector.
Note
IN must be connected to the left and OUT to the right.
Component overview PoE injector 1p S
Symbol | Explanation |
|---|---|
A | Casing in powder-coated sheet metal. |
B | Space for battery. |
C | Power supply unit. |
D | PoE injector. |
E | Cable entries. |
Wall mounting
Use four screws suitable for the wall to mount the cabinet.
The distance between the screw head and the wall should be 1.5–2 mm.
Preferably leave a 100 mm air gap around the unit.
Connecting the battery
Battery wiring is mounted on the circuit board upon delivery. Pictures below only show how to connect wiring.
Place the battery in the cabinet with the battery terminals up.
Connect the battery cable. Red cable on plus and black cable on minus.
If possible, disconnect mains voltage when replacing the battery.
Connect the terminals correctly so that you do not damage the equipment.
Alarm card for PRO3
Relay card - description, connections and alarm outputs.
No | Terminal no | Explanation |
|---|---|---|
1 | J1 | Port (RJ-45) LAN incoming. |
2 | J3 | 12 V power supply. |
3 | J2 | Port (RJ-45) PoE (LAN + 12 V) outgoing. |
Warning
The card is powered for connection of PoE device on the output (3).
The card is fed with voltage, 12 v, and takes data into the same page. On the other side (DATA OUT) PoE device can be connected.
Commissioning - how to start the device
After connection, start-up must take place in the following steps:
Plug in batteries.
First connect cables from motherboard to battery terminals.
Then connect fuse between battery.
Connect load.
Plug in the mains.
The unit works normally when the indicator LED on the outside of the cabinet door lights up with a solid green light. See front panel for other status indications.
Product data sheet
PoE
PoE injector with 1 port.
Technical specifications
These technical specifications are subject to change without notice.
Name, article number and e-number
Name | Article number | E-number (SV) |
|---|---|---|
PoE injector 1p S | SM01000012P02001PU | 51 719 50 |
More information
About PoE from Milleteknik
The series is designed to power PoE devices such as access systems, surveillance cameras and other equipment that can be operated with Power over Ethernet.
PoE Injector 1p S
PoE Injector is used when the distance between PoE device and connection (switch) is too long. The PoE injector is a power injector that makes it possible to power PoE devices at longer distances. The battery in the unit continues to power the injector when the steady power supply is lost. The product must be used indoors and is not suitable for outdoor use.
Power over Ethernet from Milleteknik
PoE for security applications.
Proven, reliable technology.
For fixed installation.
Swedish made.
Areas of use
Power supply for camera surveillance and other applications that can be powered by PoE.
To boost PoE powered devices.
Fixed installation
The product is intended for fixed installation. The battery backup must be installed by a qualified installer.
Battery types
The ECO series can be used with AGM batteries. Do not mix types of batteries, brand or used and new batteries.
Regulations and certifications
Requirements that the product meets
EMC: | EMC Directive 2014 / 30EU |
Electricity: | Low voltage directive: 2014/35 / EU |
PoE: | IEEE 802.3af, IEEE 802.3at/30.8 W Note that 802.3at type2 is not supported, as the PoE card lacks a handshake function for type 2. |
CE: | CE directive according to: 765/2008 |
Emission: | EN61000-6-: 2001 EN55022: 1998: -A1: 2000, A2: 2003 Klass B, EN61000-3-2: 2001 EN55022 (CISPR22) Class B, EN61000-3-2,-3 |
Expected operating time in the event of a power failure ( with new batteries)
PoE | Battery | Power 15.4 W | Power 30.8 W | Power 62 W | Power 90 W | Power 100 W | Power 120 W | Power 180W | Power 240 W |
|---|---|---|---|---|---|---|---|---|---|
PoE injector 1p S (12 V) | 1 psc 7.2 Ah | 3 h 50 min. | 1 hour 40 minutes | - | - | - | - | - | - |
Circuit boards - Technical data
Technical data: PoE card
Product | Number of PoE / LAN ports | Max power per port | PoE, continuous power | Ethernet type | Network ports | Interface | Functions | Type, injector and switch |
|---|---|---|---|---|---|---|---|---|
PoE injector 1p S | 1/1 | 30,8 @ 54,6 V DC | 30,8 W | Fast Ethernet Mbit PoE switch | 10 / 100 PoE | 1000Base-T RJ-45 | Auto-negotiation, Auto-uplink (auto MDI/MDI-X) | Unmanaged. There is no software interface to control the switch. |
The product lacks advanced control electronics
This product does not have a motherboard.
Power supply
Power supply - Technical Data LRS-75-12
In: |
|---|
Info | Explanation |
|---|---|
Output voltage | 13.6 V |
Output current | 0 A - 6 A |
Output voltage, ripple | 120 mVp-p |
Overvoltage | 13.8 V - 16.2 V |
Voltage recharge, ripple / current limitation | Less than 0.6 Vp-p |
Efficiency | 84.5% |
Current limitation | 110% - 180% |
Constant voltage | +/- 1.0% |
Regulatory accuracy | + / - 0.5% |
Input current (230 V) | 1,2 A |
Mains voltage frequency | 47 Hz- 63 Hz |
Mains voltage | 85 V AC - 264 V AC |
Brand effect | 25,2 W |
Temperature range | -30°C - +70°C |
Humidity range | 20% - 90% RH non-condensed |
Technical data enclosures
Enclosures - Technical Data S
Info | Explanation |
|---|---|
Name | S |
Enclosure class | IP 20 |
Measure | Height: 230 mm, width: 216 mm, depth: 85 mm. |
Height units | - |
Mounting | Wall |
Ambient temperature | + 5 ° C - + 40 ° C. For best battery life: + 15 ° C to + 25 ° C. |
Environment | Environmental class 1, indoors. 20% ~ 90% relative humidity |
Material | Powder coated sheet |
Color | White |
Cable entries, number | 3 |
Batteries that fit | 1 pc 12 V 2.3 Ah or 2 pcs 12 V 2.3 Ah or 1 pcs 12 V, 7.2 Ah. |
Place for fan | No |
Link to the latest information
Products and software are subject to updates, you will always find the latest information on our website.
Warranty, support, country of manufacture and country of origin
Warranty
The product has a two-year warranty, from the date of purchase (unless otherwise agreed). Support during the warranty period can be reached at support@milleteknik.se or telephone, +46 31-34 00 230. Compensation for travel and / or working hours in connection with locating faults, installing repaired or replaced goods is not included in the warranty. Contact Milleteknik for more information. Milleteknik provides support during the product's lifetime, however, no later than 10 years after the date of purchase. Switching to an equivalent product may occur if Milleteknik deems that repair is not possible. Support costs may (at Milleteknik's discretion) occour after the warranty period has expired.
Support
Do you need help with installation or connections? Our support phone is available: Monday-Thursday 08: 00-16: 00 and Fridays 08: 00-15: 00. Telephone support is closed between 11: 30-13: 15.
You will find answers to many questions at: www.milleteknik.se/support
Phone: +46 31-340 02 30
Support is open: Monday-Thursday 08:00-16:00, Fridays 08:00-15:00. Closed 11:30-13:15.
Spare parts
Contacted support for questions about spare parts.
Support after the warranty period
Milleteknik provides support during the life of the product, but no longer than 10 years after the date of purchase. Replacement for an equivalent product may occur if the manufacturer deems that repair is not possible. Costs for support and replacement are added after the warranty period has expired.
Questions about product performance?
Contact sales: 46 31-340 02 30, e-mail: sales@milleteknik.se
Country of manufacture
Country of manufacture / country of origin is Sweden. For more information, contact your seller.
Designed and produced by: Milleteknik AB
Designed and produced by Milleteknik AB
Batteries - recommended, not included
Batteries are not included they are sold separately
Batteries are sold separately.
7.2 Ah, 12 V AGM battery
Fits in | Number of batteries |
|---|---|
PoE injector 1p S | 1 |
Battery type | V | Ah |
|---|---|---|
Maintenance-free AGM, lead-acid battery. | 12 V | 7.2 Ah |
Article number | E-number | Article name | Terminal | Measure. Height width depth | Weight per piece | Make |
|---|---|---|---|---|---|---|
MT113-12V07-01 | 5230536 | UPLUS 12V 7.2Ah 10+ Design Life battery | Flat pin 6.3 mm | 151 x 65 x 100 mm. | 2.4 kg | UPLUS |
About translation of this document
User manual and other documents are in the original language in Swedish. Other languages are machine translated and not reviewed, errors may occur.
Product life cycle, environmental impact and recycling
The product is designed and constructed for a long service life, which reduces the environmental impact. The product's service life depends on, among other things, environmental factors, mainly ambient temperature, unforeseen load on components such as lightning strikes, external damage, handling errors, and more. Products are recycled by being handed over to the nearest recycling station or sent back to the manufacturer. Contact your distributor for more information. Costs that arise in connection with recycling are not reimbursed.
Address and contact details
Milleteknik AB |
Ögärdesvägen 8 B |
S-433 30 Partille |
Sweden |
+46 31 340 02 30 |
info@milleteknik.se |
www.milleteknik.com |